Thanks !!!
ron
Search found 1399 matches
- Wed Apr 24, 2024 9:32 am
- Forum: Body & Interior
- Topic: Shovel Mounting
- Replies: 2
- Views: 104
- Tue Apr 23, 2024 2:50 pm
- Forum: Body & Interior
- Topic: Shovel Mounting
- Replies: 2
- Views: 104
Shovel Mounting
A Swiss shovel has been laying around and I want to mount in my 710K Wheel Well. The Mount for the Blade is present. I have a Handle mount to attach but not sure where the heck it should go. If anyone happens to have their Phone and Head in your 710 Drivers side Wheel Well can you take a PIX of the ...
- Mon Apr 22, 2024 9:19 am
- Forum: Electrical
- Topic: Hooked up Battery wrong
- Replies: 2
- Views: 141
Re: Hooked up Battery wrong
If I understand the "Oops" you connected the Batteries as: (-B1+ to +B2- ) In that case, the effective output voltage would essentially be the difference between the two batteries and either slightly negative or positive -- assuming these two batteries are approximately equal. OK, well wha...
- Thu Apr 18, 2024 11:54 am
- Forum: Drivetrain
- Topic: noise bearing or pinion rear axle 712
- Replies: 2
- Views: 225
Re: noise bearing or pinion rear axle 712
If it's only under load, e.g. going up a grade, it's a difficult problem to isolate. Going under the premise that: noise = wear = Hot. You might want to try an Infrared Thermometer pointing at BOTH diff's to see if there's a significant difference -- as well as each of the four rear portals. You mig...
- Tue Apr 02, 2024 9:04 pm
- Forum: Engine
- Topic: Exhaust Pipe Flex
- Replies: 7
- Views: 506
Re: Exhaust Pipe Flex
Should be Stainless Steel -- no paint necessary.
At least mine are..
At least mine are..
- Thu Mar 28, 2024 12:03 pm
- Forum: Engine
- Topic: 2013 CB Performance Black Box Programmable Timing Control Module
- Replies: 5
- Views: 387
Re: 2013 CB Performance Black Box Programmable Timing Control Module
For what it's worth, attached is my advance curve for a 710 EFI. This would be applicable to low MAP pressure (less vacuum, heavy load). Although the MAP at low load is only an additional 4 degrees of advance and would be applicable at Idle and low load situations. The contribution to advance due to...
- Thu Mar 21, 2024 3:10 pm
- Forum: Engine
- Topic: 2013 CB Performance Black Box Programmable Timing Control Module
- Replies: 5
- Views: 387
Re: 2013 CB Performance Black Box Programmable Timing Control Module
The advance curve in the manual is not necessarily the most ideal for this engine per se. It's what could be achieved mechanically and reasonable for this engine. It also is the most simple advance mechanism which is solely based on RPM. Detonation timing also would benefit from knowing what the loa...
- Mon Mar 18, 2024 9:21 am
- Forum: Engine
- Topic: Changing piston, cylinders and cylinder heads
- Replies: 19
- Views: 1303
Re: Changing piston, cylinders and cylinder heads
A shop with VW and Porche experience is ideal, your in good hands.
I'd be curious what he finds w.r.t. Valve seating. I do buy some
engine parts from S-Tec.
I'd be curious what he finds w.r.t. Valve seating. I do buy some
engine parts from S-Tec.
- Sun Mar 17, 2024 11:14 am
- Forum: Engine
- Topic: Changing piston, cylinders and cylinder heads
- Replies: 19
- Views: 1303
Re: Changing piston, cylinders and cylinder heads
There was more than one source for casting heads. There should be a casting mark on each head. See if they are identical. In any case, no matter how good the mating surfaces look, hand lap them. If they are pretty good to start with then it's a quick and more of a verification. Otherwise, the one wi...
- Sun Mar 17, 2024 9:45 am
- Forum: Engine
- Topic: Changing piston, cylinders and cylinder heads
- Replies: 19
- Views: 1303
Re: Changing piston, cylinders and cylinder heads
It's disappointing when you get something new and it's not perfect :o But, these aren't "New" they are "New Old Stock" cast some 50 years ago. They won't be perfect. They got moved and kicked around from one storage loc to another. Qualitatively, they look usable to me. A figure ...
- Sat Mar 16, 2024 3:07 pm
- Forum: Engine
- Topic: Changing piston, cylinders and cylinder heads
- Replies: 19
- Views: 1303
Re: Changing piston, cylinders and cylinder heads
Most probably if the valves came installed they were seated.
It would be a very poor practice to just stick them in not grind
to the proper seating.
My last rebuild I acquired 4 new heads and they did not include
the Valves -- that's why I asked.
It would be a very poor practice to just stick them in not grind
to the proper seating.
My last rebuild I acquired 4 new heads and they did not include
the Valves -- that's why I asked.
- Sat Mar 16, 2024 9:36 am
- Forum: Engine
- Topic: Changing piston, cylinders and cylinder heads
- Replies: 19
- Views: 1303
Re: Changing piston, cylinders and cylinder heads
Yup, and nicely honed at that.
Oh, curious, did the S-Tec heads come with the Valves seated and installed?
Oh, curious, did the S-Tec heads come with the Valves seated and installed?
- Fri Mar 15, 2024 2:47 pm
- Forum: Engine
- Topic: Changing piston, cylinders and cylinder heads
- Replies: 19
- Views: 1303
Re: Changing piston, cylinders and cylinder heads
The protective coating must be removed. Some have reported that soaking in Diesel fuel will dissolve the coating, followed by squirts of Brake clean. As far as honing the cylinders, if you look down the bore you should see cross-hatching marks which would indicate they were honed at the factory -- w...
- Sat Mar 02, 2024 5:03 pm
- Forum: Brakes, Suspension, Steering & Tires
- Topic: Hydraulic Lines
- Replies: 10
- Views: 5037
Re: Hydraulic Lines
The locker light is pretty conclusive. If you want a more positive mechanical confirmation. For rear locker: Lift one rear tire off the ground. Put Tranie in neutral; ...with rear locker OFF lifted tire will spin freely ...with rear locker ON lifted tire is now locked to the rear tire on the ground....
- Fri Mar 01, 2024 9:56 am
- Forum: Brakes, Suspension, Steering & Tires
- Topic: Hydraulic Lines
- Replies: 10
- Views: 5037
Re: Hydraulic Lines
Slave cylinders have bleeders. But it's possible someone broke one off. They can be pretty frail at times. Attached is a PIX showing the loc of the bleeder -- compliments of Swiss Army Vehicles. If one is broken off, you could either pull the Slave and replace it, or pull it and attempt to extract t...