Search found 1404 matches
- Wed May 15, 2024 9:20 am
- Forum: Engine
- Topic: Megasquirt MS3Pro Mini ECU
- Replies: 3
- Views: 252
Re: Megasquirt MS3Pro Mini ECU
Curious.... Where did you install the O2 sensor?
- Wed May 15, 2024 9:17 am
- Forum: Electrical
- Topic: Battery going dead
- Replies: 9
- Views: 2124
Re: Battery going dead
I've had this Molex hand crimper for years, never has failed me and works for other "similar" type barrel terminals. Expensive but don't settle for a knockoffs. Amazon link below, you can search for better prices out of places like Digikey etc. P/N 63811-1000 https://www.amazon.com/Molex-6...
- Wed May 15, 2024 9:08 am
- Forum: Engine
- Topic: crankcase ventilation
- Replies: 9
- Views: 2552
Re: crankcase ventilation
For years my EFI 710 ran with no Crank ventilation, like a 50's era car vented to the atmosphere. Couple of years ago after I did a top end rebuild, I decided to be nicer to the environment and correct that and connect to the vacuum vent side of the throttle body -but- I also decided to add a Oil ca...
- Tue Apr 30, 2024 9:47 pm
- Forum: Electrical
- Topic: Power Port Connection
- Replies: 6
- Views: 309
- Mon Apr 29, 2024 8:58 pm
- Forum: Electrical
- Topic: Battery going dead
- Replies: 9
- Views: 2124
Re: Battery going dead
If you remove the top front "tin" which is forward of the Front Carb, that will
give you acess to the back side of the alternator and the Molex connector.
You do NOT have to pull the carbs.
give you acess to the back side of the alternator and the Molex connector.
You do NOT have to pull the carbs.
- Wed Apr 24, 2024 9:32 am
- Forum: Body & Interior
- Topic: Shovel Mounting
- Replies: 2
- Views: 259
Re: Shovel Mounting
Thanks !!!
ron
ron
- Tue Apr 23, 2024 2:50 pm
- Forum: Body & Interior
- Topic: Shovel Mounting
- Replies: 2
- Views: 259
Shovel Mounting
A Swiss shovel has been laying around and I want to mount in my 710K Wheel Well. The Mount for the Blade is present. I have a Handle mount to attach but not sure where the heck it should go. If anyone happens to have their Phone and Head in your 710 Drivers side Wheel Well can you take a PIX of the ...
- Mon Apr 22, 2024 9:19 am
- Forum: Electrical
- Topic: Hooked up Battery wrong
- Replies: 2
- Views: 398
Re: Hooked up Battery wrong
If I understand the "Oops" you connected the Batteries as: (-B1+ to +B2- ) In that case, the effective output voltage would essentially be the difference between the two batteries and either slightly negative or positive -- assuming these two batteries are approximately equal. OK, well wha...
- Thu Apr 18, 2024 11:54 am
- Forum: Drivetrain
- Topic: noise bearing or pinion rear axle 712
- Replies: 2
- Views: 690
Re: noise bearing or pinion rear axle 712
If it's only under load, e.g. going up a grade, it's a difficult problem to isolate. Going under the premise that: noise = wear = Hot. You might want to try an Infrared Thermometer pointing at BOTH diff's to see if there's a significant difference -- as well as each of the four rear portals. You mig...
- Tue Apr 02, 2024 9:04 pm
- Forum: Engine
- Topic: Exhaust Pipe Flex
- Replies: 7
- Views: 890
Re: Exhaust Pipe Flex
Should be Stainless Steel -- no paint necessary.
At least mine are..
At least mine are..
- Thu Mar 28, 2024 12:03 pm
- Forum: Engine
- Topic: 2013 CB Performance Black Box Programmable Timing Control Module
- Replies: 5
- Views: 1803
Re: 2013 CB Performance Black Box Programmable Timing Control Module
For what it's worth, attached is my advance curve for a 710 EFI. This would be applicable to low MAP pressure (less vacuum, heavy load). Although the MAP at low load is only an additional 4 degrees of advance and would be applicable at Idle and low load situations. The contribution to advance due to...
- Thu Mar 21, 2024 3:10 pm
- Forum: Engine
- Topic: 2013 CB Performance Black Box Programmable Timing Control Module
- Replies: 5
- Views: 1803
Re: 2013 CB Performance Black Box Programmable Timing Control Module
The advance curve in the manual is not necessarily the most ideal for this engine per se. It's what could be achieved mechanically and reasonable for this engine. It also is the most simple advance mechanism which is solely based on RPM. Detonation timing also would benefit from knowing what the loa...
- Mon Mar 18, 2024 9:21 am
- Forum: Engine
- Topic: Changing piston, cylinders and cylinder heads
- Replies: 19
- Views: 2584
Re: Changing piston, cylinders and cylinder heads
A shop with VW and Porche experience is ideal, your in good hands.
I'd be curious what he finds w.r.t. Valve seating. I do buy some
engine parts from S-Tec.
I'd be curious what he finds w.r.t. Valve seating. I do buy some
engine parts from S-Tec.
- Sun Mar 17, 2024 11:14 am
- Forum: Engine
- Topic: Changing piston, cylinders and cylinder heads
- Replies: 19
- Views: 2584
Re: Changing piston, cylinders and cylinder heads
There was more than one source for casting heads. There should be a casting mark on each head. See if they are identical. In any case, no matter how good the mating surfaces look, hand lap them. If they are pretty good to start with then it's a quick and more of a verification. Otherwise, the one wi...
- Sun Mar 17, 2024 9:45 am
- Forum: Engine
- Topic: Changing piston, cylinders and cylinder heads
- Replies: 19
- Views: 2584
Re: Changing piston, cylinders and cylinder heads
It's disappointing when you get something new and it's not perfect :o But, these aren't "New" they are "New Old Stock" cast some 50 years ago. They won't be perfect. They got moved and kicked around from one storage loc to another. Qualitatively, they look usable to me. A figure ...