Search found 274 matches

by Garrycol
Sun Feb 24, 2019 7:25 pm
Forum: Haflinger engine and driveline
Topic: Haflinger Engine Tune
Replies: 4
Views: 190
Australia

Re: Haflinger Engine Tune

In lower gears it is like a governor kicking in at 4000rpm. With the throttle flat to the floor it just does nothing but if you ease off the throttle and reapply it picks up a bit and improves. In 5th gear it is just lacking power and will no get much over 4000rpm.

Garry
by Garrycol
Fri Feb 22, 2019 1:25 am
Forum: Haflinger engine and driveline
Topic: Haflinger Engine Tune
Replies: 4
Views: 190
Australia

Re: Haflinger Engine Tune

It has bigger valves but all this was done many years ago. Something has changed with my latest tinkering but I cannot work it out.
by Garrycol
Thu Feb 21, 2019 9:45 pm
Forum: Haflinger engine and driveline
Topic: Haflinger Engine Tune
Replies: 4
Views: 190
Australia

Haflinger Engine Tune

This follows on from here http://real4x4forums.com/PinzgauerBBS/posting.php?mode=reply&f=7&t=11706 but is a different issue so new thread. The engine is 762cc and with the standard NDIX Carb normally runs really well except for the minor idle issue when hot mentioned in the link. The vehicle will pu...
by Garrycol
Wed Jan 09, 2019 4:43 pm
Forum: Haflinger engine and driveline
Topic: Haflinger Engine Idle - Carb
Replies: 2
Views: 201
Australia

Re: Haflinger Engine Idle - Carb

I do not have a governor on this engine - completely removed.
by Garrycol
Wed Jan 09, 2019 2:13 am
Forum: Haflinger engine and driveline
Topic: Haflinger Engine Idle - Carb
Replies: 2
Views: 201
Australia

Haflinger Engine Idle - Carb

Posted this over on the TheHaflinger Forum but thought I would also post here to pick up the Pinz and Mog expertise on the Zenith NDIX Carb. I am doing a tune on my engine and need to set the idle mixtures. I have the engine warmed and the idle mixture screws wound out half a turn and idle upped to ...
by Garrycol
Sat Dec 15, 2018 10:09 pm
Forum: Haflinger engine and driveline
Topic: Haflinger Engine Oil
Replies: 5
Views: 327
Australia

Re: Haflinger Engine Oil

The term Wt is a bit before my time but googling 30wt it it comes up as 10W30 and the oil chart has a temp range of 10c to 30c.

This might be Ok for northern climates but here in an Aust summer it will need a 40wt (or higher) to deal with summer temps. We are regularly above 40 in mid summer.

Garry
by Garrycol
Fri Dec 14, 2018 6:52 pm
Forum: General chat
Topic: Very dangerous winch mount
Replies: 13
Views: 641
Australia

Re: Very dangerous winch mount

Now Warn sell them for their winches so I would say that they are safe if used as designed. Now the fitment on the Pinz is not as they are deigned - that are not supposed to held in with just the pin as shown in the pic. They are designed to be inserted all the way up to the hilt in a 2" receiver th...
by Garrycol
Fri Dec 14, 2018 3:53 am
Forum: General chat
Topic: Very dangerous winch mount
Replies: 13
Views: 641
Australia

Re: Very dangerous winch mount

That is just a normal portable winch mount freely available at many 4wd shops. I plugs into a standard 2" tow receiver tow bar and if used correctly as designed is quite safe though I do agree that it does not like it is being used as designed on that Pinz. Mount is supposed to be right up close to ...
by Garrycol
Thu Dec 13, 2018 3:57 am
Forum: Haflinger engine and driveline
Topic: Haflinger Engine Oil
Replies: 5
Views: 327
Australia

Re: Haflinger Engine Oil

Good old fashioned mineral engine oil - 10w40 or the more usual 15W40. On old engines go up to #W50.

I did try Full Synthetic 5W30 once and the engine did not like it one bit - was almost as if I put water in it, so stay away from Full Synthetic.
by Garrycol
Fri Nov 23, 2018 8:43 pm
Forum: Electrical
Topic: Different approach to the rev limiter
Replies: 3
Views: 263
Australia

Re: Different approach to the rev limiter

The 24v Land Rover FC 101 has them as standard on their engines but most owners glue them open as it is really not needed. My Haflinger does not have a mechanical rev limiter so I have fitted one of these https://www.ebay.co.uk/itm/AccuSpark-Rev-Limiter-for-traditional-ignitions-4-6-8-cyls-/18171602...
by Garrycol
Wed Sep 26, 2018 8:22 pm
Forum: Haflinger engine and driveline
Topic: Haffy Transmission repair
Replies: 6
Views: 850
Australia

Re: Haffy Transmission repair

Go to Jim - even from Aust I have sought his advice and parts and he is exceptional to deal with Just remember that even with perfect synchros you have to slow right down to change down from 3rd to second - almost a stop. So maybe it is something you have to accept - 2nd gear on my vehicle is really...
by Garrycol
Wed Aug 01, 2018 8:32 pm
Forum: Haflinger engine and driveline
Topic: Are the old weber and NDIX carbs interchangeable?
Replies: 14
Views: 1643
Australia

Re: Are the old weber and NDIX carbs interchangeable?

My Haflinger has a Mog NDIX carb on it but has a Haflinger jet block in it. My engine originally had a Solex 34PBI on which did run ok but was problematic from time to time so I decided to convert to a correct NDIX . I bought a Mog carb and bought a second hand dismantled jet block from Haflinger Te...
by Garrycol
Wed Jun 27, 2018 1:17 am
Forum: Haflinger engine and driveline
Topic: Curious on wheel berrings
Replies: 5
Views: 762
Australia

Re: Curious on wheel berrings

As John has indicated you dont need to any specialist tools - just a big mallet, a mid size puller, a big screw driver to prise things, a socket set and spanners etc - common to most home workshops. Now you may very well have a dud wheel bearing but they run in oil not grease so they rarely wear out...
by Garrycol
Wed Jun 20, 2018 1:45 am
Forum: General chat
Topic: Can You Hand Crank A Pinz Gasoline Engine?
Replies: 12
Views: 652
Australia

Re: Can You Hand Crank A Pinz Gasoline Engine?

Being a mil vehicle of that era I am surprised that there is no means of hand cranking a Pinz. Certainly my Landrover 101 V8 can be hand cranked and I have done it - is not all that hard cranking the V8.
by Garrycol
Sun Apr 22, 2018 8:00 pm
Forum: Haflinger engine and driveline
Topic: 4x100 and wobble nuts?
Replies: 4
Views: 460
Australia

Re: 4x100 and wobble nuts?

Going from 98mm to 100mm with wobble nuts on a Haflinger would be fine - now I would not consider on something like a Corvette or Ferrari but on a Haflinger no issues. Just make sure the shape/contour of the wobble nit matches the wheel hole. I bought a set of 12" Minilites that I thought were 100mm...