Search found 248 matches

by bbolander
Thu Apr 02, 2020 2:09 pm
Forum: Engine
Topic: Engine Oil Level Too High
Replies: 39
Views: 8875
United States of America

Re: Engine Oil Level Too High

Re-opening this thread since I have a similar issue. @bbolander, are you sure the original fuel pump was not at fault? Early in the thread you said you saw fuel underneath it upon removal, but then later you felt the choke-plate misadjustment was the issue and you thought the pump was fine as were ...
by bbolander
Mon Mar 30, 2020 4:29 pm
Forum: Engine
Topic: Engine Oil Level Too High
Replies: 39
Views: 8875
United States of America

Re: Engine Oil Level Too High

Re-opening this thread since I have a similar issue. @bbolander, are you sure the original fuel pump was not at fault? Early in the thread you said you saw fuel underneath it upon removal, but then later you felt the choke-plate misadjustment was the issue and you thought the pump was fine as were ...
by bbolander
Thu Dec 06, 2018 5:36 pm
Forum: General chat
Topic: Best Book for Amateur Radio Technician license
Replies: 6
Views: 1415
United States of America

Re: Best Book for Amateur Radio Technician license

Gordon West Technician Class Manual • Covers FCC Question Pool Effective July 1, 2018 - June 30, 2022 for FCC Examination
by bbolander
Mon Mar 12, 2018 2:07 pm
Forum: General chat
Topic: We’re back baby!
Replies: 38
Views: 4923
United States of America

Re: We’re back baby!

Thanks everyone, I like it!
by bbolander
Sun Feb 25, 2018 5:48 pm
Forum: Electrical
Topic: Flasher Relay
Replies: 6
Views: 2099
United States of America

Re: Flasher Relay

I managed to fit mine to the top hole, wasn't easy.
IMG_1656 copy.jpg
IMG_1656 copy.jpg (526.54 KiB) Viewed 1239 times
by bbolander
Sat Nov 25, 2017 12:33 pm
Forum: Body & Interior
Topic: OEM seat bottom removal and install
Replies: 2
Views: 1176
United States of America

Re: OEM seat bottom removal and install

If you haven't done this before, a couple of pictures.

The frame has prongs to hold the cushion flaps on, the flaps have holes in them for the prongs.
IMG_2787 copy.jpg
IMG_2787 copy.jpg (494.84 KiB) Viewed 918 times
IMG_2788 copy.jpg
IMG_2788 copy.jpg (413.67 KiB) Viewed 918 times
IMG_2790 copy.jpg
IMG_2790 copy.jpg (466.66 KiB) Viewed 918 times
by bbolander
Sat Nov 25, 2017 12:28 pm
Forum: Body & Interior
Topic: OEM seat bottom removal and install
Replies: 2
Views: 1176
United States of America

Re: OEM seat bottom removal and install

Thanks to pcolette for the better OEM drivers seat cushion. Got it installed today. Getting the flaps off of the frame prongs was easy with tugs on the flap with linesman's pliers. I had to bend the prongs up to get the replacement seat on though. Fortunately only one of them broke off. The old seat...
by bbolander
Mon Nov 20, 2017 11:23 am
Forum: Engine
Topic: Fuel pump replacement
Replies: 2
Views: 947
United States of America

Re: Fuel pump replacement

Not hard to remove and replace and a new base gasket comes with the pump. I thought I had a bad fuel pump with fuel in the engine oil, but the pump turned out to be fine, the carbs were the source of the fuel in the oil. We ended using the same NAPA M60175 fuel pump that was on the Pinz before we st...
by bbolander
Mon Nov 20, 2017 11:02 am
Forum: Body & Interior
Topic: Speedometer removal
Replies: 8
Views: 1886
United States of America

Re: Speedometer removal

rmel wrote:Your current tire size versus stock ?
Posted above.
by bbolander
Thu Nov 16, 2017 5:01 pm
Forum: Body & Interior
Topic: Speedometer removal
Replies: 8
Views: 1886
United States of America

Re: Speedometer removal

I think you have it covered. The 90 degree angle fitting is optional; I think if you check it carefully you will find that the output (the side that goes into the speedo) is several percent faster than the input. If your mechanical speedo reads faster than it should, remove the 90 degree unit and c...
by bbolander
Fri Nov 10, 2017 9:08 am
Forum: Body & Interior
Topic: Speedometer removal
Replies: 8
Views: 1886
United States of America

Re: Speedometer removal

I think you have it covered. The 90 degree angle fitting is optional; I think if you check it carefully you will find that the output (the side that goes into the speedo) is several percent faster than the input. If your mechanical speedo reads faster than it should, remove the 90 degree unit and c...
by bbolander
Thu Nov 09, 2017 8:13 pm
Forum: Body & Interior
Topic: Speedometer removal
Replies: 8
Views: 1886
United States of America

Speedometer removal

Lots of good threads on speedometer repair, but didn't see any on speedometer removal. I'm ready to take mine out for repair or replacement. Here's what I'm guessing needs to be done. Remove the burled trip odometer knob on the front side of the dash via the set screw, and the nut on the dash front ...
by bbolander
Wed Nov 01, 2017 2:43 pm
Forum: Electrical
Topic: Got the Ham and CB radios mounted, DC outlet for GPS next
Replies: 29
Views: 6115
United States of America

Re: Got the Ham and CB radios mounted, DC outlet for GPS nex

We found that it's very hard to hear the Ham and CB radios going at highway speeds. So today I added external speakers to both. Used a Yaesu MLS-100 speaker like I have in my Rubicon for the Yaesu FT-7900R ham radio, and a Uniden Bearcat BC-7 speaker for the Uniden Pro 520XL CB. The MLS-100 speaker ...
by bbolander
Sat Oct 28, 2017 2:45 pm
Forum: Engine
Topic: Cold air lever
Replies: 2
Views: 1313
United States of America

Re: Cold air lever

Resurrecting an old thread I know. Since we rebuilt our 710M carbs last spring the Pinz has been running clean, smooth and strong, whether on the highway, long dirt roads, mountain grades or crawling. We'd probably driven it about 600 miles. Elevations from 1500 to 9300 ft. And, getting about 15 mpg...
by bbolander
Mon Sep 25, 2017 2:12 pm
Forum: Engine
Topic: Carburetor acceleration pumps trouble
Replies: 5
Views: 1465
United States of America

Re: Carburetor acceleration pumps trouble

We had a similar problem on ours, replaced the pump suction and pressure valves and the accelerator pump jets and nozzles, runs great now. Fuel was dripping from the nozzles. Probably could have purchased rebuilt carbs for not a lot more than what we spent on rebuilding ours.