Search found 17 matches

by jafi
Wed Sep 19, 2018 6:10 am
Forum: Electrical
Topic: Rev limiter
Replies: 4
Views: 4022
United States of America

Re: Rev limiter

Finally had time to monkey with the pinz...no start. Ended up being the flamethrower coil. Called Pertronix as the coil ohms ok on both primary and secondary. They confirmed my suspicions. Re-installed the military coil....ignition is fine once again. Bypassed the rev limiter to avoid future issues....
by jafi
Sun Sep 09, 2018 10:37 am
Forum: Electrical
Topic: Rev limiter
Replies: 4
Views: 4022
United States of America

Re: Rev limiter

Thanks much!
I am hoping to have a few minutes today to attack it...
Thanks again to both of you....tracing wires is always a pain....
I will post my results....
by jafi
Fri Sep 07, 2018 11:36 am
Forum: Electrical
Topic: Rev limiter
Replies: 4
Views: 4022
United States of America

Rev limiter

Hello all, My 710K has been running like a top...very pleased! However in the last couple days I have had the ignition cut out intermittently at different rpms. I wish to bypass the dreaded rev limiter as I see other people have had issues with it at all rpms. Where is this located? I have not looke...
by jafi
Sat Aug 18, 2018 9:17 am
Forum: Body & Interior
Topic: Eberspacher B3L C
Replies: 1
Views: 1694
United States of America

Eberspacher B3L C

Does anyone here by chance have a service manual for this?
Happy to pay for it.
I have already tried Eberspacher. Its obsolete of course and they could not provide one.
Thanks very much in advance!
by jafi
Mon Jul 30, 2018 6:15 am
Forum: Electrical
Topic: SSI issues
Replies: 10
Views: 4711
United States of America

Re: SSI issues

Thanks much for the offer Pinzinator! Unfortunately, I checked ALL of those things as well as everything else I could think of including quadruple checking voltages when off and when running, changing ground locations, adding extra ground to chassis, purchasing new batteries and completely removing ...
by jafi
Sun Jul 08, 2018 11:29 pm
Forum: Electrical
Topic: SSI issues
Replies: 10
Views: 4711
United States of America

Re: SSI issues

Yes. Followed instructions to the "T". Even Re-installed in case I somehow missed something. Yes, I have also talked to Rick several times. When I was working in a shop as a mechanic for a living, there were several instances where we had something go amiss that no one could figure out...o...
by jafi
Thu Jun 21, 2018 10:03 pm
Forum: Electrical
Topic: SSI issues
Replies: 10
Views: 4711
United States of America

Re: SSI issues

From posts here as well as from manufacturer of SSI, I time it to 2 degrees BTDC. To do so you must do the math to find how far from TDC each degree is. Then simply measure and mark 2 degrees BTDC or whatever your pinz runs best at. I should also mention to those who may respond, I have made certain...
by jafi
Thu Jun 21, 2018 6:19 am
Forum: Electrical
Topic: SSI issues
Replies: 10
Views: 4711
United States of America

SSI issues

Hello all, At the beginning of the year I purchased the SSI...with all the positive reviews (like everyone else) I thought it to be an awesome upgrade. Unfortunately, my Pinz has not run right since. I find that the timing is off by as much as 4 degrees after running it a while. I have proper voltag...
by jafi
Mon Dec 04, 2017 7:40 pm
Forum: Body & Interior
Topic: Intake tunnel insulation
Replies: 2
Views: 2128
United States of America

Re: Intake tunnel insulation

Looks like I was on the right track...thanks for the info....
by jafi
Mon Dec 04, 2017 7:04 am
Forum: Body & Interior
Topic: Intake tunnel insulation
Replies: 2
Views: 2128
United States of America

Intake tunnel insulation

Hello all!
Has anyone replaced the stock insulation/sound proofing in the intake tunnel? If so, what did you use and is it working well?
Thanks much...
by jafi
Tue Jul 11, 2017 6:11 am
Forum: Engine
Topic: Fan belt nut seized??
Replies: 6
Views: 3173
United States of America

Re: Fan belt nut seized??

Unfortunately, yes I am using the tool and yes I am turning the nut in the correct direction. I was shocked at how tight it is. I am not sure whether it is over torqued or seized as there is little sign of corrosion. That is not uncommon though if its rusted/corroded on the threads...
by jafi
Mon Jul 10, 2017 11:47 pm
Forum: Engine
Topic: Fan belt nut seized??
Replies: 6
Views: 3173
United States of America

Fan belt nut seized??

Hello all, So, I decide to change my fan belt as the current one looks very rough. I cannot get the fan nut to budge! Even resorted to the 1/2" impact...no luck. I have of course already applied some lube in an effort to get the nut to break loose. Before I get medieval on this I would very muc...
by jafi
Tue Apr 04, 2017 7:23 pm
Forum: CLASSIFIEDS: Pinzgauers, Haflingers and Volvos For Sale. Parts and Goods too!
Topic: 710 k for sale Granite Bay, Ca nice looking rig
Replies: 8
Views: 3996
United States of America

Re: 710 k for sale Granite Bay, Ca nice looking rig

Does anyone on here know any of the history of this 710K?
I am actively looking for one...
by jafi
Sat Apr 01, 2017 1:29 pm
Forum: General chat
Topic: 710K Transport
Replies: 2
Views: 1819
United States of America

710K Transport

Hello all, I may be picking up a 710K next weekend and trailering it home. This is my first one so I would like to know the best way to anchor vehicle on trailer. I have done quite a bit of trailer hauling with some large loads. However any advice would be helpful...what to avoid etc. Learning the h...