Search found 197 matches

by boeing7873
Mon Apr 06, 2020 3:30 pm
Forum: Owner builds, customizations & accessories
Topic: My awesome 710K air conditioning installation.
Replies: 13
Views: 14810
Argentina

My awesome 710K air conditioning installation.

I am proud of my two years of playing with the design and installation of an AC in my 710K. I managed to get a standard "of the shelf" cheap AC kit and install it without drilling a single hole in the trucks body, except for the gearbox access cover in the back floor. The major challenges....
by boeing7873
Sun Mar 22, 2020 8:55 pm
Forum: Body & Interior
Topic: Gas heater debug
Replies: 7
Views: 4988
Argentina

Re: Gas heater debug

I have posted somewhere around some diagrams, most likely for the old version, you have the new version, but still look around and you may find diagrams. No experience with this model. You have two options, find those diagrams, then navigate through "the Samba" forums, and try to figure th...
by boeing7873
Sun Mar 22, 2020 8:38 pm
Forum: Body & Interior
Topic: Gas heater debug
Replies: 7
Views: 4988
Argentina

Re: Gas heater debug

I have posted somewhere around some diagrams, most likely for the old version, you have the new version, but still look around and you may find diagrams. No experience with this model. You have two options, find those diagrams, then navigate through "the Samba" forums, and try to figure th...
by boeing7873
Wed Jan 08, 2020 10:17 pm
Forum: Engine
Topic: Sitting 4+ years, checklist for resurrection...
Replies: 48
Views: 27872
Argentina

Re: Sitting 4+ years, checklist for resurrection...

"Air filter is fine. No mice remnants anywhere to be found. Hopefully I'll have some more time this weekend to tinker with it." Just to make sure... rodents like the far back right corner in side the fan tunnel. They come from the bottom or through the fan. There is no way to see this but ...
by boeing7873
Tue Dec 10, 2019 8:50 pm
Forum: Body & Interior
Topic: 3D Printing Pinz Parts
Replies: 10
Views: 6502
Argentina

Re: 3D Printing Pinz Parts

Don't forget!
by boeing7873
Sun Dec 01, 2019 8:46 pm
Forum: Engine
Topic: Can't find vaccum leak. Backfiring, missing on acceleration.
Replies: 37
Views: 22105
Argentina

Re: Can't find vaccum leak. Backfiring, missing on accelerat

One more iteration on my search for the solution to this problem... I have smoked the carbs, installed, and found leaks in the cold start plate covers, they were bent. Also, my carb springs... one broken, one missing altogether!!! Answering the previous 2 posts: not sure in what part of the precess ...
by boeing7873
Sun Dec 01, 2019 8:35 pm
Forum: Engine
Topic: Choke cover leak - help!
Replies: 2
Views: 3094
Argentina

Re: Choke cover leak - help!

Both covers were pretty bent. I heated them and with soft and small hammer and vice pressure, managed to get them quite close to flat, then a little sand and both look good now.
Now back to ground zero: re-jetting, re-idle, re-synch, re-timing... :{
by boeing7873
Sat Nov 30, 2019 5:59 pm
Forum: Engine
Topic: Oh no!! Lean cylinder!!!!
Replies: 13
Views: 7421
Argentina

Re: Oh no!! Lean cylinder!!!!

Well, just to close this topic... here is the link to what I think may have been the problem.

http://real4x4forums.com/PinzgauerBBS/v ... 12&t=11968

Choke cover body leak.
by boeing7873
Thu Nov 21, 2019 11:25 pm
Forum: Engine
Topic: Choke cover leak - help!
Replies: 2
Views: 3094
Argentina

Choke cover leak - help!

So after 3 years of chasing an idle and low RPM issue, I got to the conclusion that it was related to a lack of fuel at that rpm range. Lack of fuel meant no power/stall until rpms reach 1300-1400, then all normal. I managed to eliminate the stall by pulling out the idle mixture screws way out of ra...
by boeing7873
Thu Nov 21, 2019 2:37 am
Forum: Body & Interior
Topic: 3D Printing Pinz Parts
Replies: 10
Views: 6502
Argentina

Re: 3D Printing Pinz Parts

it would be great to have the gear... but if it is a regular spur gear, a photocopy in any flie format would work.
Or measurements. I have not played with the gear extension of my CAD software yet.
Do you have the broken gear?
by boeing7873
Tue Nov 19, 2019 7:19 pm
Forum: Body & Interior
Topic: Has anyone made a Pinzgauer 3d Model?
Replies: 2
Views: 4608
Argentina

Re: Has anyone made a Pinzgauer 3d Model?

I think there are a few in Thingiverse.com
by boeing7873
Tue Nov 19, 2019 12:54 pm
Forum: Body & Interior
Topic: 3D Printing Pinz Parts
Replies: 10
Views: 6502
Argentina

Re: 3D Printing Pinz Parts

I would love to get into that gear! Having said that, what material is the original, how many are needed, if it is just for one... Really worth the effort? I am not looking to make any $$ out of this, lets make it clear, I would just expect help in convering cost. But since I will donate my time, I ...
by boeing7873
Tue Nov 19, 2019 3:58 am
Forum: Body & Interior
Topic: 3D Printing Pinz Parts
Replies: 10
Views: 6502
Argentina

3D Printing Pinz Parts

I am curious about what is actually needed in terms of parts that could be printed in plastic or TPU (Oil/Gas resistant rubber).
Someone mentioned the green lenses for the 4x4/DifLock panel, the horn button... anyone with ideas suggestions?
by boeing7873
Sat Nov 02, 2019 1:06 am
Forum: Body & Interior
Topic: Original Swiss Reflector and Eberspacher BN4 BN 4 Heater parts
Replies: 0
Views: 4780
Argentina

Original Swiss Reflector and Eberspacher BN4 BN 4 Heater parts

Gents, (Any lady driving a Pinz here?) My reflectors on my Pinz were burnt by sun and time. SAV offers a replacement but you have to drill new holes... not my type of thing. Therefore, I bought I set from the local hardware store and printed adapters to make them fit in the original Swiss frame. I h...
by boeing7873
Wed Oct 23, 2019 11:03 pm
Forum: Engine
Topic: Oil api
Replies: 5
Views: 4455
Argentina

Re: Oil api

I would not worry into looking for the original oil equivalent. All modern oils well exceed the original requirements. I live in Atlanta, about 30F to 100F temp range... And I go between 20W40 and 20W50..