GARAGE´S LINTEL TOO LOW

Issues with shocks/springs, tires, stopping, etc.
Post Reply
User avatar
MACH
Mexico
Posts: 25
Joined: Fri Mar 27, 2015 11:07 pm
Location: San Luis Potosi

GARAGE´S LINTEL TOO LOW

Post by MACH »

I moved to an apartment building with an underground garage. the entrance`s lintel is to low , I changed for smaller tires and now I can get in but in order to exit I have to drive out in reverse ( if I exit forward my Pinz – 710 m -hits the lintel with the roof´s antenna plate but I have enough clearance in the back of the roof ) ¿ is there an easy way to lower the front like half an inch ?

THANKS IN ADVANCE
User avatar
VinceAtReal4x4s
Admin
United States of America
Posts: 1974
Joined: Mon Apr 12, 2004 10:36 pm
Location: Ca. or lost in South West USA
Contact:

Re: GARAGE´S LINTEL TOO LOW

Post by VinceAtReal4x4s »

Put several sandbags in it then remove when you clear it.
"For those who risk, life has a flavor the protected shall never enjoy"

Your donation makes this site possible!

Image
User avatar
rmel
United States of America
Posts: 1312
Joined: Sun Sep 25, 2011 12:19 pm
Location: Woodside, CA
Contact:

Re: GARAGE´S LINTEL TOO LOW

Post by rmel »

Somewhat surprised you can drive in forward direction but not drive out in
the forward direction. Is there a grade change across the threshold of the
door? By the way, if the toe-in is correct, driving in the forward direction
will increase the height of the truck from ground level by 1 to 2 inches.
Conversely, going in reverse you get more stout. You could also try airing
down the fronts to 10 to 12 psi. if your that close to making it.
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK

Driver: Ron // KO0Q
User avatar
MACH
Mexico
Posts: 25
Joined: Fri Mar 27, 2015 11:07 pm
Location: San Luis Potosi

Re: GARAGE´S LINTEL TOO LOW

Post by MACH »

THANKS

Yes , the threshold is over a ramp with a 5.5 to 1 grade and I am not able to exit forward - only backward- When I come in there is very little clearance between my Pinz and the concrete ceiling
So I was wondering if there is something simple I could play with to loss half an inch ( maybe change the toe in )
User avatar
rmel
United States of America
Posts: 1312
Joined: Sun Sep 25, 2011 12:19 pm
Location: Woodside, CA
Contact:

Re: GARAGE´S LINTEL TOO LOW

Post by rmel »

You don’t want to mess with the toe-in. It effects on the road stability, tire wear and clearance. Air down and see it that gets up out of that trap.
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK

Driver: Ron // KO0Q
Texas710
United States of America
Posts: 240
Joined: Thu Jan 22, 2015 4:00 pm
Location: San Antonio, TX

Re: GARAGE´S LINTEL TOO LOW

Post by Texas710 »

Airing up and down on the trail is next level stuff to a lot of people (at least to me). Compressors, electrical, etc.

I always liked Jim's suggestion of using a small CO2 bottle to refill tires, no compressor needed. Seemed like an elegant solution for a couple hundred bucks.
Pols497
United States of America
Posts: 77
Joined: Sat Dec 05, 2009 7:34 pm
Location: mcalester okla

Re: GARAGE´S LINTEL TOO LOW

Post by Pols497 »

I replaced that antenna plate with a flat piece of aluminium.
Roger Melton
boeing7873
Argentina
Posts: 197
Joined: Sun Dec 21, 2008 10:50 am
Location: Atlanta
Contact:

Re: GARAGE´S LINTEL TOO LOW

Post by boeing7873 »

Move to a Pinz worthy place. :lol:
Jerome
CRJ Driver
Post Reply