Rear bumper
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Rear bumper
As I wait for my engine to come back for my hafi from Leonardo, I have decided to build a rear bumper for the Pinz.
So far I have only cut the bulk metal. This weekend I will begin the fabrication. Should weigh 65 lbs w/o the tire carrier.
I am using 1/4 inch 4x6 square tubing as it will allow for the 2 inch hitch to pass through it when connected to where the pintal was, the 1 3/4 DOM will be welded to where the stock braces come off the truck. Mounting points will be the 4 stock bolts below the rear door, the pintal bolts and the stock side braces. I will also at some point weld a s swing arm pivot into it for a swing out tire carrier.
So far I have only cut the bulk metal. This weekend I will begin the fabrication. Should weigh 65 lbs w/o the tire carrier.
I am using 1/4 inch 4x6 square tubing as it will allow for the 2 inch hitch to pass through it when connected to where the pintal was, the 1 3/4 DOM will be welded to where the stock braces come off the truck. Mounting points will be the 4 stock bolts below the rear door, the pintal bolts and the stock side braces. I will also at some point weld a s swing arm pivot into it for a swing out tire carrier.
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Re: Rear bumper
I just did this this last post with pictures using tap talk. Retry easy from my phone while standing in the garage!
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
Re: Rear bumper
So are you going to tie the body to the drivetrain then? If it connects to both the pintle tow mounts and the stock rear bumper "tubes" then that would allow a lot of vibration to be conducted and also might result in stress cracks etc???
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Re: Rear bumper
So best to go to just the stock mounts? Thats fine it will make it easer.
Thanks,
Thanks,
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Re: Rear bumper
For those that have asked, or dont remember, the front bumper fabrication is here
viewtopic.php?f=18&t=6881
I know the rear is not of the same design as the front, but this one will go together comparably quick
viewtopic.php?f=18&t=6881
I know the rear is not of the same design as the front, but this one will go together comparably quick
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
Re: Rear bumper
Keep the hitch mounting and the bumper separate.
Cum catapultae proscriptae erunt tum soli proscript catapultas habebunt.
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Re: Rear bumper
Made some progress so far, Next I need to cut and box in the 2 inch reciver pass through and cut the original bumper tubes off of the side braces so I can add the 1.75" DOM. The DOM tubing will extend to the height of the bed and will alow the installation of a removable rear hoop or other accessory down the road. The original bumper plug fits nicely in the tubing.
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Re: Rear bumper
Weekends have been busy with non-Pinz stuff but during the evenings I have been still working on the bumper replacement. As you can see the blade is finished, now I need to cut the square hole for the 2 inch recever, make the spare tire mount, and weld on the upright bars.
My question now is where should I mount the hinge pin for the tire mount. Anyone have some experience with this and want to share? Also pics of the swing arm would help.
My question now is where should I mount the hinge pin for the tire mount. Anyone have some experience with this and want to share? Also pics of the swing arm would help.
Last edited by westernair on Tue Jan 15, 2013 4:49 pm, edited 1 time in total.
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Re: Rear bumper
I also may upgrade my backup light to lights mounted in the bumper.
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
Re: Rear bumper
The bus in the backround looks interesting....
Stock means no imagination!
Volvo TGB1317, .95% Morphed!
68 Haffy
Volvo TGB1317, .95% Morphed!
68 Haffy
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Re: Rear bumper
Just another air cooled toy.M Wehrman wrote:The bus in the backround looks interesting....
Here are a few pics of it at a photo shoot last year, if you are interested
http://www.griotsgarage.com/text/conten ... hb333.html
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Re: Rear bumper
Bumper swag. 1/4 plate plasma cut
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
Re: Rear bumper
Very nice I like it the bumper and badges wish I had those fab skills.
Last edited by mopar on Tue Jan 15, 2013 5:25 pm, edited 1 time in total.
1974 712M AKA the Banana
1974 710M AKA the project truck
1987 718M Now Sold
1975 Volvo TGB1111 Now Sold
1973 Pinzgauer 712M x2 Now Sold
1963 404S Now Sold
- westernair
- Posts: 748
- Joined: Sat Jan 01, 2011 11:14 pm
- Location: Tacoma, WA
Re: Rear bumper
If people wanted some of these Pinzgauer name plates, I could produce them for $30 a pair.mopar wrote:Verry nice I like it ot wish I had those fab skills.
Shawn
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold
62 haffy Bantam
61 haffy 4 door
72 710K - Sold
73 712M - Sold