Auxillary switch placement- What have you done?
- Jimm391730
- Posts: 1456
- Joined: Wed Apr 14, 2004 10:58 pm
- Location: Idyllwild, CA
Re: Auxillary switch placement- What have you done?
Ron, where and how does all the wiring run to all your overhead consoles?
Jim M.
712W and 710M
712W and 710M
Re: Auxillary switch placement- What have you done?
Two wiring harnesses, one for the heads up which runs along the top of the door jam down the side
then into the rear compartment, sending unit wiring goes through the bulkhead into the engine compartment.
On the passenger side, goes a similar route, catching the ECU for AFR and a Fuel pressure sender in the
engine bay. All good fun, esp. when something fails you you have to debug it
then into the rear compartment, sending unit wiring goes through the bulkhead into the engine compartment.
On the passenger side, goes a similar route, catching the ECU for AFR and a Fuel pressure sender in the
engine bay. All good fun, esp. when something fails you you have to debug it
Last edited by rmel on Mon Nov 27, 2017 2:50 pm, edited 1 time in total.
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
Re: Auxillary switch placement- What have you done?
Thanks everyone for answering my questions.
Ron, how does your front overhead console attach to the K body?
Ron, how does your front overhead console attach to the K body?
75 Swiss 710K
Not so new owner but still a novice
W9YG
Not so new owner but still a novice
W9YG
Re: Auxillary switch placement- What have you done?
Sheet metal screws, there are a number of "cavities" over head that can
take a screw and not break through to the open air -- so to speak. Kind'a
works out OK, but it's not designed for easy access. If I were to do this
over, first go Aluminum for reduced weight, then design in a hinged
mounting frame with 1/2 twist locks for easy access and future mods.
take a screw and not break through to the open air -- so to speak. Kind'a
works out OK, but it's not designed for easy access. If I were to do this
over, first go Aluminum for reduced weight, then design in a hinged
mounting frame with 1/2 twist locks for easy access and future mods.
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
- GadgetPhreak
- Posts: 294
- Joined: Wed Jan 27, 2016 12:14 pm
- Location: Redmond, WA
- Contact:
Re: Auxillary switch placement- What have you done?
Mule did some, not all of the work. The overhead console we fabbed at my place and a buddy finish assembled and rhino lined it.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
King County Search & Rescue | Regional Special Vehicles Unit
1972 710M - Building up for SAR use
Follow my build, learn more, or contact me: http://www.sarpinz.com
1972 710M - Building up for SAR use
Follow my build, learn more, or contact me: http://www.sarpinz.com
- VinceAtReal4x4s
- Admin
- Posts: 2039
- Joined: Mon Apr 12, 2004 10:36 pm
- Location: Ca. or lost in South West USA
- Contact:
Re: Auxillary switch placement- What have you done?
Nutsert
"For those who risk, life has a flavor the protected shall never enjoy"
Your donation makes this site possible!
Your donation makes this site possible!
-
- Posts: 103
- Joined: Sat Dec 16, 2017 8:09 pm
- Location: TN
Re: Auxillary switch placement- What have you done?
Trying to keep everything 24v (winch and cb) but I needed a USB plug. Found this Powerwerks 24v 4.2amp plug and installed it as inconspicuously as I could as I'm trying to retain the military look. Good plug that charges galaxy 7 very quickly and was apx. $25.
- Attachments
-
- 20180125_154741.jpg (665.28 KiB) Viewed 3483 times
-
- 20180125_154800_resized_1.jpg (69.25 KiB) Viewed 3483 times
Last edited by Derrickbwg on Thu Jan 25, 2018 3:07 pm, edited 2 times in total.
1975 710K
1974 710M
2018 G63
1974 710M
2018 G63
- TechMOGogy
- Posts: 2831
- Joined: Wed Feb 01, 2012 11:39 am
- Location: Ontario, Canada
Re: Auxillary switch placement- What have you done?
I like it - where did you find the 24v usb plug?
72 Pathfinder | 75 710M 2.7i | 96 350GDT Worker
-
- Posts: 103
- Joined: Sat Dec 16, 2017 8:09 pm
- Location: TN
Re: Auxillary switch placement- What have you done?
1975 710K
1974 710M
2018 G63
1974 710M
2018 G63
- VinceAtReal4x4s
- Admin
- Posts: 2039
- Joined: Mon Apr 12, 2004 10:36 pm
- Location: Ca. or lost in South West USA
- Contact:
Re: Auxillary switch placement- What have you done?
Oh man, I wish I'd not seen that. I didn't know they made an OLED volt gauge! On my "must buy, you have no choice" list now.
https://powerwerx.com/blue-sea-1733-ole ... -voltmeter
https://powerwerx.com/blue-sea-1733-ole ... -voltmeter
"For those who risk, life has a flavor the protected shall never enjoy"
Your donation makes this site possible!
Your donation makes this site possible!