Can anyone get me a dimension of the rear door width or, preferrably, the window opening dimensions?
Looking at buying some of the sliding glass from Dave Dunn for a project I am doing.
Thanks!
Width of rear side doors on a "K" pinzgauer?
Re: Width of rear side doors on a "K" pinzgauer?
I can send you that tomorrow morning. Outta town at the moment. You want the opening frame edge to frame edge or the inside jams where the felt runners are?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
Re: Width of rear side doors on a "K" pinzgauer?
Really just need the outside opening size of the window in the door where the glass is.
Re: Width of rear side doors on a "K" pinzgauer?
Here you go...BOTH windows measured exactly the same
621mm x 414mm
621mm x 414mm
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
- David Dunn
- Posts: 2274
- Joined: Wed Apr 14, 2004 7:08 pm
- Location: Arcadia, CA
Re: Width of rear side doors on a "K" pinzgauer?
Haf-e needs the opening size, we know the glass size. It's different than the TD door opening or I could give it.
.
The Trojan Horse... the 1st Pinz used to covertly carry troops into battle .
ATL Pinzgauer XM 718K TUM(HD) 6x6 FFR (aka The Green Grail)
The Trojan Horse... the 1st Pinz used to covertly carry troops into battle .
ATL Pinzgauer XM 718K TUM(HD) 6x6 FFR (aka The Green Grail)
Re: Width of rear side doors on a "K" pinzgauer?
Thanks - but as Dave said - I need the opening size to see if I can make it work with some window frames I am considering making for the side of my pinz.
Haf-e
Haf-e
Re: Width of rear side doors on a "K" pinzgauer?
That's what I had thought you would be looking for
OK, here's the new measurements.
635mm x 430mm
That would include the felt runners. I have relatively new felt
but I did keep the old ones that were in decent shape. These
measure 4.5mm from where the glass sits to the backside metal frame.
So the TOTAL metal to metal would be approximately 644mm x 439mm
Hope this helps, if you need another measurement met me know.
ron
OK, here's the new measurements.
635mm x 430mm
That would include the felt runners. I have relatively new felt
but I did keep the old ones that were in decent shape. These
measure 4.5mm from where the glass sits to the backside metal frame.
So the TOTAL metal to metal would be approximately 644mm x 439mm
Hope this helps, if you need another measurement met me know.
ron
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q