engine timing and distributor driveshaft

Engine troubles? Try here.
Post Reply
norcal pinz
United States of America
Posts: 396
Joined: Thu May 01, 2008 11:41 pm
Location: northern california

engine timing and distributor driveshaft

Post by norcal pinz »

Hi Guys!! im Back its been like 10 years and im getting my Pinz on the road again!
Im having an issue i cannot get the timing mark to come any closer than about 40ish mm before the pin :(
when i turn the distributor in the direction it needs to go it hits the fan shroud.
i looked through the manual (page 36 sction A ) and it says its possible to move the distributor driveshaft a few teeth over but i wanted to check with you guys to see if i am correct ??
Last edited by norcal pinz on Sun Oct 04, 2020 10:00 pm, edited 2 times in total.
710M 1972
710k 1974
User avatar
rmel
United States of America
Posts: 1394
Joined: Sun Sep 25, 2011 12:19 pm
Location: Woodside, CA
Contact:

Re: engine timing and distributor driveshaft

Post by rmel »

Perhaps your distributor is rotated about 160 degrees out of position
and you just need to rotate in the opposite direction nearly 1/2 clock?
Seems odd that it had worked before (even in the distant past) and
now the inner geared shaft has to be pulled and re-aligned ?
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK

Driver: Ron // KO0Q
norcal pinz
United States of America
Posts: 396
Joined: Thu May 01, 2008 11:41 pm
Location: northern california

Re: engine timing and distributor driveshaft

Post by norcal pinz »

it seems really odd but I'm almost positive that I need to move the distributor driveshaft over a tooth or two. the manual says the shaft should be 90 degrees to the driving direction and mine is not. i made sure the #1 piston is at TDC and the timing marks on the distributor and flywheel at #1 when i removed the distributor the shaft underneath was not at 90 degrees. i have no clue how the truck was running fine.
710M 1972
710k 1974
User avatar
rmel
United States of America
Posts: 1394
Joined: Sun Sep 25, 2011 12:19 pm
Location: Woodside, CA
Contact:

Re: engine timing and distributor driveshaft @ 90 degrees

Post by rmel »

Going on the assumption it ran well before, then I suspect the slotted shaft
of the distributor is clocked 180 degrees out of place. Rotate the slot position
then you may be able to rotate the body of the distributor in the opposite
direction away from the cooling shroud. Just think'n ://
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK

Driver: Ron // KO0Q
User avatar
pcolette
United States of America
Posts: 1614
Joined: Sun Dec 10, 2006 7:38 pm
Location: Southwest Wisconsin

Re: engine timing and distributor driveshaft @ 90 degrees

Post by pcolette »

The cogs (teeth) on the bottom of the shaft are not 180 deg opposed through their centers, so it's unlikely that the distributor could be removed and rotated. It's possible that the internal plate, weights and springs have become corroded over time and now need a good cleaning and lubricating.
IMG_3469.jpeg
IMG_3469.jpeg (271.88 KiB) Viewed 3688 times
Paul C.
_________
'73 Swiss 710M
'89 Puch 230GE
User avatar
rmel
United States of America
Posts: 1394
Joined: Sun Sep 25, 2011 12:19 pm
Location: Woodside, CA
Contact:

Re: engine timing and distributor driveshaft @ 90 degrees

Post by rmel »

Ha!! Good catch Paul,

I forgot about the slot/tooth being off-center :shock:
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK

Driver: Ron // KO0Q
norcal pinz
United States of America
Posts: 396
Joined: Thu May 01, 2008 11:41 pm
Location: northern california

Re: engine timing and distributor driveshaft @ 90 degrees

Post by norcal pinz »

im reffering to the distributor driveshaft its inside the engine and accesable through the same hole the distributor goes in look at the manual page 36, Fig. 79, section A its possible to move it over a tooth and that was my problem.
what are you using to share pictures i tried to upload some but it failed
710M 1972
710k 1974
User avatar
pcolette
United States of America
Posts: 1614
Joined: Sun Dec 10, 2006 7:38 pm
Location: Southwest Wisconsin

Re: engine timing and distributor driveshaft

Post by pcolette »

I didn't realize that you could remove and adjust that internal shaft that drives the distributor. I learned something new.

I simply drag the jpeg files into the reply box and they automatically upload. I then check the "place inline" box that appears after the file uploads.
Paul C.
_________
'73 Swiss 710M
'89 Puch 230GE
Post Reply